phone +38 (067) 445-60-35
Call request

CNC Drilling Center KD-612KHS

In stock
  • 6 side drilling
  • 3 drilling heads: 12 - horizontal spindles, 35 - vertical spindles (35 - top, 9 - bottom)
  • 2 routers spindles for 5.5 kW (top) and 3.5 kW (bottom)
  • Grooving saw X-axis
  • Panel length: 70-2800 mm
  • Panel width: 35-1200 mm
  • Axis speed, X/Y/Z 140/90/50 m/min
  • Dust removal conveyor
  • Rear conveyor
  • 2 workpiece drilling mode

 

 

 

 

 

 

 

 

 

 

Purpose

CNC drilling center KD-612KHS with three drilling groups (2 from above and 1 from below) for drilling from 6 sides and a grooving saw is designed for high-precision drilling of through and blind holes in the ends and planes of furniture panels, which allows processing any additive maps in one pass of the part. The machine is equipped with two milling units for milling both simple straight grooves, such as a groove for the back wall or the bottom of a box, and profiling.

Scheme of drilling groups

drilling head diagram KDT KD-612KHS

Distinctive features

  • Ability to work with optimizer programs with drilling maps, as well as print labels;
  • High processing speed: 140/90/50 m/min;
  • Grooving unit - saw 120 mm;
  • Milling unit as standard;
  • Drilling from 6 sides;
  • Additive of small-sized details from 70*35 mm;
  • Automatic lubrication of X and Y travel guides;
  • Two options for unloading parts from the machine "back / forward";
  • Automatic unloading table;
  • Visualization of the processing of a double-sided additive map;
  • Batch drilling mode is enabled;
  • Scanner for reading the additive card by barcode.

Design advantages

Machine control panel
CAD/CAM control panel with barcode reading capability to increase machine productivity.
barcode reader
A barcode scanner is included in the basic equipment of the machine.
drilling group
There are 3 drilling groups installed on the machine: 12 - horizontal spindles, 35 - vertical spindles (26 - from above, 9 - from below). 2 milling units (5.5 kW + 3.5 kW) are installed as standard.
drilling from 6 sides
The machine can process two panels at the same time, both top and bottom, within one working cycle, thanks to the possibility of drilling from 6 sides.
milling unit
2 milling spindles 5.5 kW + 3.5 kW, 18000 rpm (top and bottom) for sawing straight and curved grooves.
grooving knot
Grooving unit with a saw (disk diameter 120 mm).
Batch drilling mode
Batch drilling mode - processing of two parts at the same time with a mirror map.
Drilling Map Optimizer
Ability to work with all popular programs for optimizing drilling maps and printing labels.
powerful welded frame
The machine bed was developed taking into account CAD programs, where the maximum allowable loads and requirements for the machine design were calculated and simulated. The welded frame is tempered to relieve all internal stresses in the material, then processing takes place on a five-axis metalworking machine, where all platforms and holes for mounting components and assemblies are milled.
chip conveyor
The machine in the basic configuration has a conveyor for removing chips and small residues of workpieces.
air cushion work tables
Easy movement of parts on the table occurs due to the air flow supplied by a special electric fan through the holes in the upper part of the table, thereby eliminating the possible appearance of scratches on the lower surface of the part.
automatic workpiece holding clamps
Two automatic clamps will allow you to securely fix the workpiece with a length of 70 mm. up to 2800 mm and perform fewer interceptions during drilling, which significantly increases the speed of the work cycle compared to machines with a single grip.
strong vertical clamp
The powerful vertical clamp securely positions the workpiece. Works synchronously with the drilling unit.
mobile stoves
Mobile plates in the drilling area allow for through milling.
side equalizer
Lateral workpiece leveler.
operator protection
Protecting the operator from injury.
unloading table
Finished parts exit area with cross conveyor, equipped with workpiece detection sensor.
minimum workpiece size
The minimum workpiece size is 70x35 mm, which allows for the addition of small-sized parts.
electric cabinet
Sealed dust and moisture resistant cabinet with electronic components from the world's leading manufacturers is removed from the processing area, which prolongs the service life of electrical components and provides ease of maintenance.
Characteristics of CNC Drilling Center
Workpiece length, mm 70-2800
Workpiece width, mm 35-1200
Workpiece thickness, mm 9-60
Workpiece gripper travel speed (X), m/min 140
Maximum speed along the axis (Y), m/min 90
Maximum speed along the axis (Z), m/min 50
Number of drilling groups, pcs 3
Number of vertical spindles (upper group), pcs 26
Number of vertical spindles (lower group), pcs 9
Number of horizontal spindles, pcs 12
Milling unit, kW 1x5,5 + 1x3,5
Grooving unit (saw blade size), mm 120x20x4
Suction pipe diameter, mm 1x100 + 1x150 + 1x200
Full power, kW 28,2
Working pressure, MPa 0.6
Machine dimensions (LxWxH), mm 6040x3140x2190
Weight, kg 4000

NOTE!

Specifications and appearance of the product are subject to change without notice.
Get price
Your selection:

© 2023 KDT Woodworking Machines